Code by B.M.

git-svn-id: https://svn.fhem.de/fhem/trunk@816 2b470e98-0d58-463d-a4d8-8e2adae1ed80

fhem/FHEM/00_LIRC.pm

@@ -17,6 +17,7 @@ LIRC_Initialize($)
 
 # Provider
   $hash->{ReadFn}  = "LIRC_Read";
+  $hash->{ReadyFn} = "LIRC_Ready";
   $hash->{Clients} = ":LIRC:";
 
 # Consumer
@@ -33,13 +34,14 @@ LIRC_Define($$)
 
   $hash->{STATE} = "Initialized";
 
+  $hash->{LircObj}->clean_up() if($hash->{LircObj});
   delete $hash->{LircObj};
   delete $hash->{FD};
 
   my $name = $a[0];
   my $config = $a[2];
 
-  Log 3, "LIRC opening LIRC device $config";
+  Log 3, "LIRC opening $name device $config";
   my $lirc = Lirc::Client->new({
         prog    => 'fhem',
         rcfile  => "$config", 
@@ -53,9 +55,11 @@ LIRC_Define($$)
   $select->add( $lirc->sock );
 
   $hash->{LircObj} = $lirc;
-  $hash->{FD} = $lirc->sock;
+  
-  $selectlist{"$name.$config"} = $hash;
+  $hash->{FD} = $lirc->{sock};       # is not working and sets timeout to undefined 
-  $hash->{SelectObj} = $select;
+  $selectlist{"$name"} = $hash;      # 
+  $readyfnlist{"$name"} = $hash;     # thats why we start polling
+  $hash->{SelectObj} = $select;      
   $hash->{DeviceName} = $name;    
   $hash->{STATE} = "Opened";
 
@@ -68,7 +72,10 @@ LIRC_Undef($$)
 {
   my ($hash, $arg) = @_;
 
-  $hash->{LircObj}->close() if($hash->{LircObj});
+  $hash->{LircObj}->clean_up() if($hash->{LircObj});
+  delete $hash->{LircObj};
+  delete $hash->{FD};
+
   return undef;
 }
 
@@ -85,11 +92,22 @@ LIRC_Read($)
     # an ir event has been received (if you are tracking other filehandles, you need to make sure it is lirc)
     my @codes = $lirc->next_codes;    # should not block
     for my $code (@codes){
-      Log 3, "LIRC code: $code\n";
+      Log 3, "LIRC $code toggle";
       DoTrigger($code, "toggle");
     }
   }
 
 }
 
+#####################################
+sub
+LIRC_Ready($)
+{
+  my ($hash) = @_;
+
+  my $select= $hash->{SelectObj};
+
+  return $select->can_read(0);
+}
+
 1;

fhem/docs/commandref.html

@@ -2233,51 +2233,64 @@ A line ending with \ will be concatenated with the next one, so long lines
   <ul>
     <code>define &lt;name&gt; CUL_HM &lt;6-digit-hex-code&gt;</code>
     <br><br>
-    Try to avoid this command with the <a href="#autocreate">autocreate</a>
+    Normally this command is generated by the <a
-    module enabled. Now you have two possibilities, both as a set command to
+    href="#autocreate">autocreate</a> module, together with the necessary
-    the corresponding CUL device: <a href="#CULset">hmPairForSec</a> and
+    hmClass and subType attributes. Usually you issue a <a
-    <a href="#CULset">hmPairSerial</a>.
+    href="#CULset">hmPairForSec</a> command and press the corresponding button
-    <br>
+    on the device to be paired, or issue a <a href="#CULset">hmPairSerial</a>
-    If a device was not paired with the CUL, then it won't know its subType,
+    set command if the device is a receiver and you know its serial number.
-    and therefore won't be able to interpret device messages correctly.
+    Autocreate will then create a fhem device and set all necessary attributes.
+    <br><br>
+    If you cannot use autocreate, then you have to specify:<br>
+    <ul>
+      <li>the &lt;6-digit-hex-code&gt;<br>
+          which is the hardcoded address of the device (no, you cannot choose
+          it arbitrarily like for FS20 devices). You may detect it by
+          inspecting the fhem log.
+      <li>the hmClass attribute<br>
+          which is either sender or receiver
+      <li>the subType attribute<br>
+          which is one of switch dimmer blindActuator remote sensor  swi
+          pushButton threeStateSensor motionDetector  keyMatic winMatic
+          smokeDetector<br>
+          Without these attributes fhem won't be able to decode device messages
+          appropriately.
+
+    </ul>
   </ul><br>
 
   <a name="CUL_HMset"></a>
   <b>Set</b>
   <ul>
-     General commands (available to all hm devices):
+     Note: devices which are normally send-only (remote/sensor/etc) must be set
+     into pairing/learning mode in order to receive the following commands.
+     <br>
+     <br>
+
+     General commands (available to most hm devices):
      <ul>
-     <li>raw &lt;data&gt; ...<br>
+     <li>statusRequest<br>
-         Only needed for experimentation.
+         Send a status request to the device.
-         send a list of "raw" commands. The first command will be immediately
-         sent, the next one after the previous one is acked by the target.  The
-         length will be computed automatically, and the message counter will be
-         incremented if the first tw charcters are ++.
-         Example (enable AES):<pre>
-         set hm1 raw ++A001F100001234560105000000001\
-                     ++A001F10000123456010802010AF10B000C00\
-                     ++A001F1000012345601080801\
-                     ++A001F100001234560106<pre>
          </li>
      <li>reset<br>
-         Factory reset the device. You need to pair it again to use it.
+         Factory reset the device. You need to pair it again to use it with
+         fhem.
          </li>
      <li>pair<br>
-         Pair the device again with its known serialNumber
+         Pair the device again with its known serialNumber (e.g. after a device
-         </li>
+         reset).  </li>
-     <li>statusRequest<br>
-         Send a statusRequest to the device.
-         </li>
-
      </ul>
+     <br>
      subType (i.e family) dependent commands:
      <ul>
+     <br>
      <li>switch
        <ul>
           <li>on [forSec] - set the switch on</li>
           <li>off - set the switch off</li>
           <li>toggle - toggle the switch.</li>
        </ul></li>
+     <br>
      <li>dimmer, blindActuator
        <ul>
          <li>0 - 100 with a resolution of 0.5:<br>
@@ -2285,6 +2298,7 @@ A line ending with \ will be concatenated with the next one, so long lines
          <li>on / off<br>
              this corresponds to 100 or 0 %.
        </ul></li>
+     <br>
      <li>4Dis (HM-PB-4DIS-WM)
        <ul>
          <li>text &lt;btn_no&gt; [on|off] &lt;text1&gt; &lt;text2&gt;<br>
@@ -2298,6 +2312,23 @@ A line ending with \ will be concatenated with the next one, so long lines
              </ul>
        </ul></li>
      </ul>
+     <br>
+
+     Debugging:
+       <ul>
+         <li>raw &lt;data&gt; ...<br>
+             Only needed for experimentation.
+             send a list of "raw" commands. The first command will be immediately
+             sent, the next one after the previous one is acked by the target.  The
+             length will be computed automatically, and the message counter will be
+             incremented if the first tw charcters are ++. 
+             Example (enable AES):<pre>
+   set hm1 raw ++A001F100001234560105000000001\
+               ++A001F10000123456010802010AF10B000C00\
+               ++A001F1000012345601080801\
+               ++A001F100001234560106<pre>
+             </li>
+       </ul>
   </ul><br>
 
   <a name="CUL_HMget"></a>
@@ -3054,12 +3085,32 @@ A line ending with \ will be concatenated with the next one, so long lines
 <a name="LIRC"></a>
 <h3>LIRC</h3>
 <ul>
+  Can use infrared signals received by an lirc device as toggle events.
+  <br>
   <br>
 
   <a name="LIRCdefine"></a>
   <b>Define</b>
   <ul>
-    <code>define &lt;name&gt; LIRC &lt;device&gt;</code>
+    define &lt;name&gt; LIRC &lt;lircrc_file&gt;<br>
+    Example:<br>
+    <ul>
+     define Lirc LIRC /etc/lirc/lircrc
+    </ul>
+    Note: In the lirc configuration file you have to define each possible event.
+    If you have this configuration
+    <pre>
+    begin
+      prog = fhem
+      button = pwr
+      config = IrPower
+    end</pre>
+    and you press the pwr button the IrPower toggle event occures at fhem. 
+    <pre>
+    define IrPower01 notify IrPower set lamp toggle</pre>
+    turns the lamp on and off.
+    If you want a faster reaction to keypresses you have to change the
+    defaultvalue of readytimeout from 5 seconds to e.g. 1 second in fhem.pl
   </ul>
   <br>